Product portfolio

SEMIKI measurement solution

SoC test system Vision Camera System PCB function tester Chip loading machine Repair measuring equipment

Electronic industry measuring machine

Multi-channel data logger Standard AC/DC programmable power supply High voltage meter Insulation resistance tester Ground resistance meter Leakage current meter ESD measuring device Electrical characteristics analysis equipment Production room equipment

Force and mechanical measuring equipment

Force measuring device clamp set Force sensor Force measuring base Torque wrench Force measuring system Decibel Material thickness gauge Vibration meter Gas meter Mechanical force gauge Electronic force gauge Torque measuring machine Speed machine Device for measuring material hardness Power screwdriver

Measuring equipment for mechanical industry

Standard measuring tools Thread check conditioner Profile measuring machine Coating thickness gauge Quality testing machine Magnetic measuring device Altitude measure

Temperature and humidity measuring device

Temperature and humidity meter Substance concentration measuring device Detachable probe thermometer Infrared thermometer, thermal camera Self-recording thermometer

Optical measuring equipment

Industrial cameras Measurement microscope Digital microscope Stereo microscope Beam intensity meter Colorimeter Endoscopy equipment

Lab equipment

Industrial scales Desktop scale Technical scales Analytical balance Industrial floor scales Hanna experimental measuring equipment Clean room equipment Spectroscopy and X-Ray equipment Simulation cabinets, drying cabinets, furnaces

MITSUBOSHI BELT PENCIL tension alignment device

Producer: GATE UNITTA

Categories: Mechanical force gauge, Device for measuring material hardness Tag: MITSUBOSHI BELT PENCIL

The V-Belt pencil type belt tension measuring and testing device is used to evaluate and align the appropriate belt tension according to the manufacturer's standards. For each different type of belt, new and used, the rotation speed will have different tension. Alignment is usually performed periodically 24-48 hours after the line becomes operational. Alignment is very important to evaluate belt quality, tension and durability, helping the line operate stably.

MITSUBOSHI Japan

Pencil type

belt tension gauge

V-Belt Tension Gauge

Proper tension is the key to long, efficient, trouble-free belt operation. When you install a new set of belts, use the gauge to establish correct tension.

Then, to maintain performance, re-check belt tension after 24-48 hours. The payoff is maximum belt life, reduced downtime and uninterrupted equipment service.

Belt Tension testers are for checking concerns on your synchronous belt drives and V-Belt.

How To Check V-Belt Tension

Proper drive belt tension is a critical setting on your factory. A loose drive belt can cause problems like wavy cuts or diving blades. An overtightened drive belt can cause premature wear and failure on many parts of the sawmill including cylindrical drive bearing, drive belt, and even engine failure.

The drive belt used on your factory is a V belt design. The V belt transfers power from the drive pulley to the driving pulley. A properly tensioned belt will sit in the V groove of the pulley so that the sides of the belt are the only surfaces touching. This position allows the belt to grip the pulley and still has some slippage if the drive gets in a bind.

The only way to properly set the drive belt tension is to use a belt tension gauge (MITSUBOSHI V-Belt tension gauge pencil type ). Belt tension is set by the amount of pounds (force) it takes to move the tightened belt a set amount of inches. To find this setting for your sawmill, refer to the Drive Belt Tension Measurement Guide on this page or review in your sawmill manual.

Manual Belt Tension Tester

The spring scale type tester measures how much force is required to deflect the belt a specified distance at the center of its span. This is the force deflection method of tensioning belts. The Sonic Tension Meter measures the vibration of the belt span and instantly converts the vibration frequency into belt static tension. This is the span vibration method of tensioning belts.

Video: How To Measure Belt Deflection | Pencil type belt tension gauge

Specification

* Load Range: 15kg

* Material: Steel plate

* Length: 200mm

* Measurement Range: 60mm

Pic.: MITSUBOSHI V-Belt tension gauge ( 15Kgf/150N) at Semiki's warehouse

Maintenance and calibration :

► We also have calibration certificate attached ( optional )

► Please re-calibrate after use for a certain period through our purchase store. Local Vietnam : SEMIKI CORP