HOTLINE: +84 979761016
Máy đo độ rung ONO SOKKI VC-2200/3200 là thiết bị tối ưu cho việc bảo trì và giám sát liên tục các cơ sở sản xuất với độ chính xác cao và chi phí thấp. Sử dụng bộ xử lý tín hiệu số (DSP) tiên tiến, VC-2200/3200 cho phép đánh giá đồng thời hai tần số khác nhau từ tín hiệu cảm biến gia tốc, đồng thời dễ dàng quản lý dữ liệu trên máy tính. Thiết bị này còn tích hợp chức năng kiểm tra trực quan và thính giác, cho phép kiểm tra độ rung qua âm thanh hoặc hiển thị trên màn hình. Chức năng “đầu vào cổng so sánh” giúp trích xuất các hiện tượng rung cần thiết một cách chính xác.
Với kích thước nhỏ gọn (96mm x 96mm) và các bộ lọc số cùng nhiều chế độ đo lường (đối với VC-3200), máy đo độ rung ONO SOKKI VC-2200/3200 là lựa chọn lý tưởng cho các ứng dụng đo lường và kiểm tra độ rung trong môi trường công nghiệp hiện đại.
The VC-2200/3200 is a Vibration comparator which is used for maintenance and constant monitoring of production facilities with high accuracy, high function, and low cost in a single unit.
The VC-2200/3200 Vibration Comparator utilizes high-speed calculation by employing a digital signal processor (DSP) in DIN size. Newly installed TEDS function enables high performance calculation, time reduction, and less human errors in setup.
From the output signal of an accelerometer, the VC-2200/3200 simultaneously judges two different frequencies with one unit. Besides, the data is easily managed with a PC. The VC-2200/3200 has multiple roles including detection, judgment, and data management.
The VC-2200/3200 features checking of “visual and auditory”. It has function of checking the vibration with sound by connecting headphones as well as checking the vibration with view by on-screen numerical displays and bar graphs.
The “comparator gate input function” is also equipped which can extract only the necessary vibration phenomenon by controlling the timing signals from a PLC. All of these functions are packed into a compact DIN size (96mm X 96mm).
Since the VC-3200 has digital filters, measurement modes more than the VC-2200, it works effectively in measurement that requires detailed judgment condition settings.
*The above photo includes Vibration Comparator (VC-2200/3200) and an accelerometer (NP-3331N30), cable (NP-0143), magnet base (NP-0100) besides.
• NEW FUNCTION
It avoids setting errors, saves your time and effort of troublesome calibration and measurement preparation.
Easily viewable small level vibration
Mute function protects ears from impulsive sound when a sensor is mounted etc.
Measurement conditions or judging conditions can be set by one command. Selectable from setting in a batch or each setting.
*The VC-3200 can memory 5 conditions depending on the product judgment conditions.
Power averaging operation and its judgment are possible.
Enables rotation and mechanical vibration measurement of reciprocating devices.
Simultaneous output of AC and DC signal for each specified band Useful for connection to FFT Analyzer or recorder
Displays vibration levels in both numericals and a bar chart on the screen.
VC-2200/3200 featuring 2-band judgment based on whether rms or peak value for each band. Judging by vibration value, more complicated judgment can be made easily.
Multi-function in a single compact body. Designed in consideration of installation to the panel.
If vibration exceeding the judgment level lasted for the specified period or longer, the comparator output can be made. It prevents misjudgment caused from human error that an operator touch the sensor with a tool etc. in mistake.
This is used for automatic judgment such as quality judgment of product lines. The timing can be controlled to measure vibration phenomena at the right time.
Vibration sound can be checked when connecting commercially available headphones. Also used as the substitute for an auscultation rod. Phenomenon of the each specified band can be checked.
The VC-3200 has a memory function. Since it remembers the setting conditions before power off, you can immediately start measurement with same setting conditions. The VC-3200 has also data memory function to memory measured data.
-Pass/fail judgment of bearing using vibration-
Rotate the bearing and detect the vibration value for judgment. By focusing on the frequency band, it is possible to know the content of detected defect (flaw, foreign material inclusion, imbalance etc.). Speed sensor is also used along with accelerometers. In that case, it is necessary to set the VC-2200/3200 in external input mode.
Related field
Detection of abnormal operation of machine tools
Detecting axial runout of a machine tool.
Axial runout of machine tools has a great influence on the accuracy of finished product. Basically the runout of axis is measured by displacement gauge, which, however, is difficult due to environmental conditions, working conditions, cost, etc. Because the VC-2200/3200 can detect abnormality of axis according to vibration level, it is not influenced by environmental conditions and can be used for usual monitoring. The greater the axial runout, the greater the vibration level. In other words, monitoring the amount of vibration continuously and checking it lead to finding abnormality of the machine tool.
Related field
Facility monitoring
-Monitoring vibration to detect abnormality of bearings, gears and other parts of production facilities without attendance-
Facility diagnosis used to take a lot of work and time. An operator must measure and keep watching vibration from the facility because the vibration change gives an indication to know the timing of parts replacement or even abnormality. The VC-2200/3200 can continuously monitor vibration to detect unusual movement, prevent it from serious breakage and save the labor. The frequency band can be specified that might indicate the abnormality.
Related field
Detection of break and wear of tool
Detecting drill bit break, tool bit break etc of operating machine tool without attendance
For the machines which process quite a large quantities of parts, such as NC machine, unattended operation is employed. If the drill bit or other tool is broken during unattended operation, it causes defective products. Reprocessing or disposal of these defective products is nothing but waste of money. The VC-2200 detects vibration when the drill bit is broken and makes stop the operation if occurred, as a result, minimizes producing defectives. Worn drill bit also lowers processing accuracy. Monitoring vibration change and checking the operation help to improve the processing accuracy.
Related field
Input section
| Number of input channels | 1 |
|---|---|
| Signal input | Switched between an accelerometer with a built-in preamplifier and an external voltage signal
*Accelerometer with a built-in preamplifier Applicable accelerometer : NP-3331B,NP-3331N20(Discon) (TEDS supported, accelerometer with a built-in preamplifier) ,NP-3331N30 (TEDS supported, accelerometer with a built-in preamplifier) ◆ When you use other than NP-3331B or NP-3331N20(Discon) ,NP-3331N30, please contact your nearest distributer or send us an e-mail (overseas@ONO SOKKI.co.jp) *External voltage signal *Input connector : C02 (BNC) |
| Cable disconnection detection function (VC-3200) |
Cable disconnection can be detected when using CCLD. Open collector output (positive) *Common to over output(selectable) |
| Sensor sensitivity setup | 1.00 x10-2 to 9.99 x102 mV/(m/s2)digital input |
| Unit setup | m/s2 or EU selectable |
| Input range | 0.1 to 50,000 m/s2 (Setup range differs depending on the sensor sensitivity.) (example : The input range will be 2.000 to 1000 m/s2 when a sensor with 5 mV/(m/s2) sensitivity is used. ) |
| Frequency characteristics | 3 Hz to 15 kHz ±0.5 dB 1.5 Hz to 20 kHz ±3 dB (160 Hz reference value) |
| Input-referenced noise | 3 Hz to 20 kHz band: 30 µVrms or less |
| Dynamic range | Through /AC : 80 dB or more(input voltage range x1, x2, x5) 70 dB or more(input voltage range x10, x20, x50, x100, x200, x500) THR(Through) : 1.5 Hz to 40 kHz bands AC : 1.5 Hz to 20 kHz bands |
| TEDS function (* Note) | Available to the TEDS sensor (IEEE1451.4)(Ver1.0 or later) |
* Non-insulated type accelerometer may be affected by the noise with the grand loop. Insulation of the sensor mount and cable routing must be performed carefully to avoid interference of noise.
* Note: If a TEDS supported sensor made by other companies is used, TEDS information may not be read depending on the type of a TEDS tip included in a sensor.
1. If you are considering the purchase of a TEDS sensor made by other companies, please consult to the manufacturer or dealer of the TEDS sensor, and perform the operation check.
2. When you want to use a TEDS sensor you already have with the TEDS supported measurement instruments made by Ono Sokki, please perform the operation check with a demonstration product of Ono Sokki. (Please consult your nearest distributor or Ono Sokki sales office nearby.)
External control signal input
| Contact input | Key protect· reset input· gate input |
|---|---|
| Input voltage range | HI : + 2.4 to + 5.0 V LOW : 0 to + 0.8 V (Non-voltage contact input available) |
| Non-voltage input | Open circuit voltage : +5 V Short circuit current : 0.5 mA or less Contact resistance : 50 Ω or less |
| RS-232C output | Provided as standard＊Transfer speed : VC-2200 9600 bps VC-3200 9600, 19200 bps ＊Connector : DIN 8-pin circular connector ＊Cable : AX-5022B |
| VC-2200 | VC-3200 | Option (bandpass-filter) | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| VC-0321 Low frequency band |
VC-0322 Intermediate frequency band |
VC-0323 High frequency band |
|||||||||
| Number of setup bands | 2 | 3 | – | – | – | ||||||
| Band filter | HPF(Highpass filter)/LPF(Lowpass filter) |
|
|
|
|
|
|||||
| *LPF(Lowpass filter) | -48dB/oct Butterworth characteristics -3 dB ± 1 dB at fc | ||||||||||
| Analog filter | LOW cut (Highpass filter) | -3 dB±1 dB -18 dB/oct at 10 Hz fc |
-3 dB±1 dB -18 dB/oct at 3Hz,10 Hz* fc |
– | – | – | |||||
| HI cut (Lowpass filter) | -3 dB±1 dB -18 dB/oct at 1 kHz, 10 kHz fc |
-3 dB±1 dB -18 dB/oct at 1 kHz* |
– | – | – | ||||||
*Low cut 10 Hz and Hi cut 1 kHz of VC-3200: Conforms to ISO 2954-2012
*fc: cutoff frequency
Calculation section
| VC-2200 | VC-3200 | |||
|---|---|---|---|---|
| Measurement mode | Selection | · RMS value · Peak value · MAX hold · Peak hold |
· RMS value · Peak value · Peak/MAX RMS factor (PEAK/rms) · MAX hold · Peak hold · Peak/MAX RMS factor hold (PEAK/rms) · Power average |
|
| RMS value | RMS value
|
RMS value
|
||
| Peak value | Peak value of time waveform absolute value | |||
| PEAK/MAX RMS factor (PRF) | None | Peak value ÷ MAX RMS value | ||
| MAX hold | Holds the MAX value of RMS value | |||
| PEAK hold | Holds the MAX value of PEAK value | |||
| PEAK/MAX RMS factor hold (PRF hold) |
None | Holds the MAX value of PEAK/MAX RMS value | ||
| Power average | None | 
*During the Power average is set, other measurement mode cannot be set. |
||
| Other avaraging function Tactmax value: TAVG |
None | Displays max. value for 500 ms.The number of average: OFF/4/8/16/32/64 selectable | ||
Output section
| Analog output | THR (through output) / AC output / DC output (AC/DC: select the output of each band)＊Output impedance : approx. 50 Ω ＊Through output Max. rated output : ±5 V Frequency range : 3 Hz to 15 kHz ± 0.5 dB, 1.5 Hz to 40 kHz ± 3 dB ＊AC output_Selectable output for each band Max. rated output : ±5 V Frequency range : 3 Hz to 15 kHz ± 0.5 dB, 1.5 Hz to 20 kHz ± 3 dB ＊DC output_Selectable output for each band(rms output) Max.rated output : 0-5 V |
|---|
• Current output function of the VC-2100 (option) : Not supported.HeadphoneAC output for each band＊Max. output : 15 mW or more to the rated impedance 24 Ω
＊Connector : φ3.5 stereo mini jackCAL signal output160 Hz, 1 V0-p ± 3 % (output from through/AC/DC)Over outputOutput when input range over or A/D over
Open collector output (negative logic)VC-2200: output when input range over and A/D over
Open collector output (positive logic)
VC-3200: output when input range over and A/D over
Open collector output (positive logic)
· Shared with disconnection detection output.
＊Voltage : DC 30 V or less
＊Sink current : 25 mA or less
Comparator output
| Function | VC-2200: Judgment is made independently for each band. Selection of either rms or peak value judgment for each bandVC-3200: Judgment is made independently for each band. Selection of rms / peak value / peak· maximum rms judgment factor for each band |
|---|---|
| Comparator level setting | Can be set in steps of 1% of the full-scale range |
| Output | Output when over or under the setup value VC-2200: Open collector output (Output positive and negative logic simultaneously) VC-3200: Open collector output (Setup selectable from positive and negative logic)＊Voltage : DC 30 V or less ＊Sink current : 25 mA or less |
| Operating time | 100 ms or less |
| Delay time setting | Selectable from 0· 0.5· 1· 1.5· 2· 3· 4· 5· 6· 7· 8· 9· 10· 15· 20 -second |
Display
| Display | LCD with backlight Measurement value display : 4-digit digital display Display update : 0.5 seconds Bar chart display (Bar-chart display update time : 0.1 seconds) (Linear/logarithmic display selectable) Comparator level display |
|---|---|
| OVER indicator | Input range over or A/D over: red light ON |
| NG indicator | Comparator NG output: red light ON |
| Comparator ON/OFF indicator | Comparator ON: green light ON |
Others
| Condition backup | Setting values are saved in memory when the power is switched OFF. |
|---|---|
| Terminal strip | M3.5 screw with square washer |
General specification
| Power supply | Rated DC24 V (±10 %) |
|---|---|
| Current consumption | 0.2 A or less (25 °C) |
| Operating temperature range | 0 to + 50 °C |
| Storage temperature rage | −5 to + 55 °C |
| Operating humidity range | 85 % RH or less (with no condensation) |
| Outer dimensions | DIN 96 x 96 x 112 mm (excluding protruded section) |
| Material | 94V0 PBT(polybutylene terephthalate) |
| Weight | Approx. 500 g |
| Option | VC-0423 Integration software (VC-2200/3200) VC-0321 Low frequency band-pass filter VC-0322 Intermediate frequency band-pass filter VC-0323 High frequency band-pass filter |
Maintenance :
► Please re-calibrate after use for a certain period through our purchase store. Local Vietnam : SEMIKI CORP
DISTRIBUTED BY:
Semiki instrumentation Co., Ltd
Email: sales@semiki.com
Office tel: +84 28 2253 3522
~DOING OUR BEST FOR YOU~
Hệ thống phân tích độ rung, Máy đo âm thanh, Máy đo độ rung động cơ
Hệ thống phân tích độ rung
Cảm biến đo độ rung, Hệ thống phân tích độ rung, Máy đo độ rung, Máy đo độ rung động cơ
Cảm biến đo độ rung, Hệ thống phân tích độ rung, Máy đo độ rung, Máy đo độ rung động cơ
Cảm biến đo độ rung, Hệ thống phân tích độ rung, Máy đo độ rung, Máy đo độ rung động cơ
Hệ thống phân tích độ rung
Máy đo độ rung động cơ
Máy đo độ rung động cơ